vScan utility locating set, incl. 1 Watt transmitter

The vScan series with transmitter and receiver – rugged cable and line locators to prevent damage during excavation work and for straightforward line tracing

This kit consists of a locating transmitter and a locating receiver. The vScan Tx 1 Watt transmitter connects directly to cables and metallic conductors such as metal pipes and applies a traceable transmit frequency to the metal. The vScan receiver picks up that frequency, which makes the conductor and its route measurable – in soil as well as in building floors.

The vScan Tx 1 Watt transmitter

The 1 Watt Transmitter for the vScan product Series has one induction frequency as well as three direct connect frequencies. The LED indicators on the transmitter show the frequency selected, output level, and battery status. An audio indicator beeps to advise the quality of the connection.

This one-watt transmitter can transmit the locate signal onto the target line three ways. By direct connection, if direct access to the line is available, by induction by simply putting the transmitter in induction mode and placing it over the target line with the induction arrow in line with it or by clamp mode and using the induction clamp to clamp around the target line.

The wide frequency range of the Transmitter makes this a very versatile transmitter. The 83kHz induction frequency makes it ideal for inducing the signal onto large diameter, direct buried iron pipes with bell and gasket connections, and for using the induction clamp around smaller pipes. The lower 512Hz and 8.192kHz are good for direct connection to trace cables, and the 83kHz direct connection is good for high resistance pipes or for use with pushrod camera systems to trace the deployed pushrod.

Packaged in a lightweight, rugged, ergonomic IP54 housing, the Transmitter provides consistent current output in direct connect, clamp, and induction modes. The Transmitter has protection against inadvertent connection to incoming voltages up to 240V. The Transmitter comes standard with direct connection leads, ground stake; clip-on carry straps, and D cell batteries.

The vScan receiver

• Sonde location (512Hz, 640Hz, 33kHz)
• Frequency location: 33kHz, 131kHz, power 50Hz, radio, metal mode (the latter on the vScan M only)
• Passive signals: 50Hz, radio and, as a free option, cathodic protection (CP) 100/120Hz
• Current measurement: helps to positively identify the target line
• Simple two-button operation: on/off and info (depth and current)
• Detachable speaker: lets you hold the speaker to your ear while continuing to measure
• Compass direction indicator: ensures correct alignment over the line
• Optional ferromagnetic object location (vScanM)
• Built-in self-test to check all functions
• Self-calibration
• Automatic data logging up to 2GB: helps identify usage and training needs
• Mini-USB port for connection to the free MyvScan software (for PC) for updates and data read-out
• Large, high-resolution, high-contrast dot matrix display: makes signal interpretation simple and intuitive
• Automatic backlight: for use after dark
• Rugged ABS housing with protective rubber boots
• 24 months warranty

The vScan system was developed specifically to avoid cable damage where pipes or other lines have to be excavated or dug up. It makes locating buried cables and pipework a simple and economical process. You do not need to be an electronics expert to use the vScan’s functions: the main functions and settings follow industry standards, so only minimal training is required. A detailed guide to locating sondes and camera heads with the vScan – including our pipe cameras with a 512Hz transmitter – sets out the procedure in detail.

The vScan locates sondes and camera heads with 512Hz, 640Hz and 33kHz transmitters as well as active frequencies of 32.768kHz and 131.072kHz. It also locates radio frequencies in the 16.5kHz to 23.9kHz range and passive power at 50Hz plus harmonics.

The vScanM is the only device in its class to offer ferromagnetic metal location. This allows covered manhole lids, valve caps, marker posts and other buried metal parts to be found. The vScan is aimed at civil engineering and road construction firms, municipalities, works yards, road maintenance depots and landscaping contractors.

The free MyvScan software for PC reads out locating data from the vScan. It also lets you configure settings on the device and download and install software updates for the vScan receiver.

Features overview of the vScan / vScanM